Trim
Fascia installation for Lakeland rooflines
The fascia board along your eaves is what the gutter fastens into and what the edge of the roof finishes against. Fascia installation replaces the whole run with new board, checks the rafter tails behind it, and sets the drip edge and gutter so they work with it. Jonathan plans it around any roof or gutter work you have coming.
Why Lakeland rooflines are coming due for new trim
Trim tends to come due at the same moment as the roof above it.
On a house like yours, the fascia may be primed wood that was painted once when the house was finished. That board has taken the same sun and rain as the shingles beside it. With much of Lakeland reaching its first roof replacement, the trim behind the gutters is often reaching the end of its first coat of paint at the same time.
Heavy tree cover speeds it along. Gutters choked with leaves overflow onto the back of the board, and in humid weather wet wood stays wet. Paint lets go first at the corners and joints, then the gutter fasteners start losing their grip. A new gutter screwed into tired fascia will hold no better than the old one did.
Spring storms test the whole edge. Between March and June, wind and heavy rain hit the eaves hard, and a board with soft spots lets a gutter sag or pull away at a seam. Replacing the run before storm season, or as part of a reroof, gives the new gutter solid wood to hang on when the weather turns.
Fascia Installation is one of the 43 things we do across the metro. The fascia installation page covers the work itself, and if something is wrong at your Lakeland property you can send over the details or call (901) 922-9450.
Running a new fascia board end to end
Old board off, framing in view
We take down the gutter and remove the old fascia along the full run, including the stretches that still look fine. With the board off, the rafter tails and any sub-fascia are exposed, and Jonathan checks each one by hand and photographs it. A soft tail gets repaired or reinforced so the new board has something solid to fasten to.
Choosing the board
Primed wood is the traditional choice and takes paint well, though it needs repainting on a schedule and every cut end primed. Cellular PVC or composite board will not rot and holds paint if you want a color. Aluminum wrap over a wood board keeps the paintbrush away for good, as long as the wood under it is sound. We price the options side by side.
Joints, corners and returns
Long runs need joints, and joints are where water gets in. We cut scarf joints at an angle rather than butting square ends together, prime every cut surface before the board goes up, and fasten with coated or stainless nails. Corners and the returns at a gable end get fitted tight so the paint line stays clean.
Drip edge and the last course
Once the board is up, drip edge goes on over the top of it so water leaving the shingles drops into the gutter and stays off the face. The last course of shingles should overhang that metal a little, enough to throw water clear of the board. If the roof is staying, we work the new drip edge in under the existing shingles with care.
Details that decide whether new fascia lasts
A fresh board looks good the day it goes up. Whether it still looks good after a few storm seasons comes down to these.

Primer on the face only
A wood board primed on the front and left bare on the back and ends soaks up water from behind the gutter. That is how a nearly new fascia ends up peeling. Every side of a wood board gets primed before installation, and every cut made on site gets primed before it is fastened.
The gutter hung before the drip edge
Hanging a gutter and then trying to slip drip edge behind it leaves a gap where water runs between the gutter and the board. The order matters: board, drip edge, then the gutter hung tight beneath the metal. When we replace gutters on the same visit, keeping that order is easy.
Metal wrapped over soft wood
Aluminum wrap over a rotted board hides the rot while the wood keeps breaking down underneath, until the gutter screws have nothing left to bite. If the board under a wrap is soft, it comes off and a sound one goes up before any metal covers it.
Rafter tails nobody checked
New fascia nailed onto rafter tails that have gone soft is only as strong as that wood. It looks fine until a gutter full of wet leaves pulls it outward. Checking the tails is part of the job while the old board is off, and repairing one then is far easier than later.
Fascia first, then gutters and the roof
If a new roof or a new gutter run is on your list, settle the fascia question before either one starts. The drip edge laps onto the board and the gutter hangs from it, so fascia replaced afterward means pulling metal and gutters back off work that just went on. Deciding up front lets one crew set all three pieces in order.
During a reroof the timing works out neatly. The shingles and old drip edge are off at the eaves, the gutters come down, and the board is right there to replace. New fascia goes up, then fresh drip edge, then the shingles, and the gutters go back last. Nothing gets disturbed twice.
When only the gutters are being replaced, the fascia decision is the same question in a smaller form. Jonathan presses along the whole run while the old gutters are still up and shows you the photos. If the wood is solid and well painted, it stays and the new gutter goes on it. If it is not, the written price covers both.
We wrote this one up at more length on the blog: Why the Fascia Comes First When New Gutters Are Going Up.
Where this work happens
Lakeland sits close to home for us, a short run out from Germantown on any working day. For the other trades, start at the Lakeland page.
Questions from Lakeland
What is the difference between fascia and soffit?
Fascia is the vertical board along the roof edge, facing out, and it carries the gutter. Soffit is the horizontal surface underneath the overhang, often vented so the attic can draw air. The two meet at the corner of the eave, so when one is replaced we check the other at the same time.
Should I replace the fascia when I get new gutters?
If the board is soft, cracked or peeling badly, yes. A new gutter is only as secure as the wood its fasteners go into. If the fascia is sound and painted, it can stay. Jonathan checks the full run and photographs it before you decide, so the call rests on what is actually there.
Is PVC fascia better than wood?
PVC and composite boards do not rot, which matters behind a gutter that sometimes overflows. Wood costs less up front and paints beautifully, though it needs a fresh coat on a schedule. Aluminum wrap over sound wood sits in between. The right one depends on your house and how much upkeep you want.
Can new fascia go up without replacing the roof?
Yes. We work beneath the bottom shingle course, take off the old drip edge, replace the board and set new drip edge back under the shingles. It takes more care than doing it during a reroof, and it is everyday work for the crew. The roof stays watertight the whole time.
What happens if the rafter tails behind the fascia are rotten?
We show you the photographs and repair them before the new board goes up. Depending on how far the rot runs, that can mean sistering new lumber to the tail or adding a sub-fascia for support. It is carpentry, and it gets priced in writing before the crew does it.
Can you match the trim color on the rest of the house?
We can. New wood or PVC board gets primed and painted to match the existing trim, and we compare against a sample from your house. Aluminum wrap comes in a range of factory colors, and we pick the closest one before ordering so the eaves read as one line.
Also handled around Lakeland
If something else on the list is close to needing attention, say so while we are out and it goes in the same quote.
What customers say
Jonathan told me when his crew arrived. They were here completing the work in one day. Gave me a great price, the best I got out of 5.
Very happy with work. No hidden charges and crew cleaned up after the work. Would highly recommend him.
Have the eaves measured for new board
Tell Jonathan whether a roof or gutter job is coming up. He will walk the roofline for a free roof look and put a real number on the fascia, with photos of every soft spot.
The phone goes straight to the owner, and a missed call comes back the same day.